4.2 KiB
| title | layout |
|---|---|
| Quick Install | docs |
Note: this guide is assuming you are using Ubuntu 18.04 LTS for installation, which comes with
ufwandnetplan, and that you have already installedgitand configuredntp. NTP configuration instructions can be found here. While it is possible to install LibreTime on other OSes, such as CentOS 7, Debian 9 and 10, and Raspbian 9 and 10, these are less tested. Firewall and static IP address configuration will need to be done according to your OSes instructions.
Minimum System Requirements
| On-Premises Install (FM + Internet Radio) | Cloud Install (Internet Radio Only) |
|---|---|
| 1 Ghz Processor | 1vCPU |
| 2 GB RAM | 2 GB RAM |
| Wired ethernet connection, static IP address | 2 TB of data transfer/month |
DigitalOcean and Linode have similar plans that meet Cloud Install requirements. Both plans cost $10/month.
Preparing the server
Configure the server to have a static IP address by modifying the Netplan configuration. If you're using a cloud VM, you likely already have a static IP address. Check with your provider to confirm this.
cd /etc/netplan && ls # find the netplan filename
sudo nano ##-netcfg.yaml
If the Netplan configuration is empty, fill in the file with the example below. Otherwise,
input the IP address reserved for the server in xxx.xxx.xxx.xxx/yy format, the gateway (the IP address
of your router), and the DNS nameserver. If you don't have a nameserver on your network,
feel free to use Cloudflare's: 1.1.1.1 and 1.0.0.1.
network:
version: 2
renderer: networkd
ethernets:
enp3s0:
addresses: [192.168.88.8/24]
gateway4: 192.168.88.1
nameservers:
addresses: 192.168.88.1
After the netplan file has been saved, run sudo netplan apply to apply changes.
Next, configure Ubuntu's firewall by running:
sudo ufw enable
sudo ufw allow 80/tcp
sudo ufw allow 8000/tcp
Unblock ports 8001 and 8002 if you plan on broadcasting live with Libretime.
sudo ufw enable 8001/tcp
sudo ufw enable 8002/tcp
If needed, instuctions for setting up a reverse proxy can be found here.
Installing LibreTime
Installing LibreTime consists of running the following commands in the terminal:
git clone https://github.com/LibreTime/libretime.git
cd libretime
sudo ./install -fiap
After the install is completed, head to the IP address of the server LibreTime was just installed on to complete the welcome wizard. While not strictly necessary, it is recommended that you change the passwords prompted in the welcome wizard if you intend on accessing the server from the Internet. The welcome wizard will walk you through the rest of the installation process.
Post-install
Services
Once all of the services needed to run LibreTime are installed and configured,
it is important that the server starts them during the boot process, to cut down on downtime, especially in live enviornments.
Ubuntu 18.04 uses the systemctl command to manage services, so run the following commands to enable all
LibreTime-needed services to run at boot:
sudo systemctl enable libretime-liquidsoap
sudo systemctl enable libretime-playout
sudo systemctl enable libretime-celery
sudo systemctl enable libretime-analyzer
sudo systemctl enable apache2
sudo systemctl enable rabbitmq-server
If an error is returned, try adding .service to the end of each command. For example:
sudo systemctl enable apache2.service
User Permissions
If you plan to have LibreTime output analog audio directly from its server to a mixing console or transmitter,
the www-data user needs to be added to the audio user group using the command below.
sudo adduser www-data audio
Congratulations! You've successfully installed LibreTime!
Now that the install is complete, use these guides to help you continue to set up your LibreTime server